Boulton Paul P.10

Le monomoteur biplan Boulton Paul P.10 tel que décrit sur Wikipedia.en

[Vous devez être inscrit et connecté pour voir ce lien]
-------------------------------------------------------------------------------------------------------------------------------------------------------------------

The Boulton & Paul P.10 was a two seat, single-engined [Vous devez être inscrit et connecté pour voir ce lien] built just after [Vous devez être inscrit et connecté pour voir ce lien] to develop techniques for the construction of all steel aircraft.

It is also notable for its first use of plastic as a structural material.
Only one P.10 was built and it attracted much attention; but it probably never flew.


Design and development

In the first decade of the 20th century, Boulton and Paul besides their wood construction shops also had plants for iron making, wire fencing and structural steel for buildings.

It is not surprising therefore that when they became involved with aircraft production in [Vous devez être inscrit et connecté pour voir ce lien] and then began their own designs they soon looked to the use of steel airframes.

The Boulton & Paul P.10 was the first example and only their third design.

The P.10 was a single-engined two-seat biplane with an airframe of high tensile steel, zinc treated and varnished against corrosion.

It had single bay wings with no stagger or sweep.

Both wings had the same span and the same constant chord. Rather like the earlier [Vous devez être inscrit et connecté pour voir ce lien], the interwing gap was large and equal to the chord, putting the upper wing high above the fuselage.

Either side of the centre section were a pair of vee struts to front and rear spars, assisted by another strut from front spar to the engine bulkhead
The wings were built around two Isection spars, each a box section constructed from rolled strips.

The forward spar had four of these strips, the rear two.

The P.10 was displayed at the Paris Salon d'Aeronautique in 1919 without its fabric covering, the wing construction was in plain view.

There were interconnected ailerons on both wings.

The P.10 had a small fin, which with its horn balanced rudder formed a teardrop shape.

The tail, with unbalanced elevators was strut braced to the fin.

The front fuselage was built on four tubular longerons, but from leading edge rearwards it consisted of a set of oval formers with stringers.
^{[Vous devez être inscrit et connecté pour voir ce lien]}
The greatest novelty of the P.10 was that this part of the fuselage was not only a monocoque structure (still fairly unusual at the time), but a monocoque of steel with a load-bearing plastic skin riveted between the formers and stringers.

Specifically, the plastic was [Vous devez être inscrit et connecté pour voir ce lien]-Dilecto, a hard, synthetic cellulose-formaldehyde product.

The company claimed it was proof against fire, heat, humidity and insects.

This was the first use of structural plastic in an airframe and perhaps the last for another sixty years.

This construction gave the fuselage a smooth, rounded "torpedo-like" look, which was enhanced by the close cowling of the 100 hp (75 kW) [Vous devez être inscrit et connecté pour voir ce lien] radial engine, though its three cylinders projected out a long way for cooling.

This engine drove a four bladed wooden propeller, the only wooden part of the airframe. Boulton Paul had made their own propellers during the war.

The front cockpit was at the wing leading edge with a rather distant second cockpit under the trailing edge, about 5 ft 6 in (1.68 m) aft.

Dual control was fitted. As exhibited in Paris, the P.10 had a tall single axle undercarriage mounted on a pair of vee-struts on either side. These were [Vous devez être inscrit et connecté pour voir ce lien] sprung, though there were plans for oleo dampers.

The P.10 was not the first metal British aircraft, for the unlikely looking [Vous devez être inscrit et connecté pour voir ce lien] holds that priority; but it never had a realistic hope of flight.^{[Vous devez être inscrit et connecté pour voir ce lien]}

One lesser novelty, which was to become a standard Boulton & Paul feature was the mounting of the Lucifer on a hinge so that it could be swung sideways for servicing without disconnecting pipework etc.

The P.10 made a big impact at the 1919 Paris show, with Flight describing it as "the machine of the show".^{[Vous devez être inscrit et connecté pour voir ce lien]}

Nonetheless, after the show the P.10 disappeared from sight.

There is no record of it flying, though there seems no reason why it should not have been capable.

There are reports of it being damaged when the engine failed.

It was not at the Paris show of 1920. Surprisingly, the delicate structures of one wing and the tail unit have survived.

These parts are now at the [Vous devez être inscrit et connecté pour voir ce lien] in Boulton & Paul's home town of Norwich, though this museum is
closed for refurbishment as of 2009. It intends to re-open in 2011.

Specifications


Data from [Vous devez être inscrit et connecté pour voir ce lien], p. 173 The performance figures are estimates only.

General characteristics

• Crew: 1
  
• Capacity: 1 passenger
  
• Length: 26 ft 0 in (7.93 m)
  
• Wingspan: 30 ft 0 in (9.14 m)
  
• Height: 12 ft 0 in (3.66 m)
  
• Wing area: 309 ft² (28.7 m²)
  
• Empty weight: 1,104 lb (501 kg)
  
• Gross weight: 1,700 lb (771 kg)
  
• Powerplant: 1 × [Vous devez être inscrit et connecté pour voir ce lien] 3-cylinder air-cooled radial engine, 100 hp (75 kW)